. INSTALLER’S SENS-IN-1D 18-HD60D29-4 GUIDE Library Service Literature Product Section Unitary Customer Property - Contains wiring, service, Product Unitary Accessory and operation information. Please retain.
Model T’stat, Panels, Timers, Relays Literature Type Installer’s Guide Sequence Date January 2001 File No. SV-UN-ACC-SENS-IN-1D 1/01 Supersedes SENS-IN-1C Model. About the Manual Literature Change History Overview of Manual SENS-IN-1A September 1997 Note: One copy of this document ships inside each Original Installation manual for mounting, wiring and pro- Programmable Zone Sensor kit and is customer gramming the Programmable Zone Sensor.
General Information Kit Inspection Remote Panel w/ NSB - BAYSENS019B This 7 day programmable sensor features 2,3 or 4 periods Upon receipt of the kit, immediately note; for Occupied or Unoccupied programming per day. If the power is interrupted, the program is retained in permanent Any visible damage to the exterior shipping package. General Information. Installation Sensor Mounting Figure 1 Removing the Sensor from the Sub Base 1.
Mounting location. Choose a location on an interior wall near the return air grille, approximately five feet above floor level, where air circulates freely and is of average temperature for the zone. Installation UCM Status Inputs (4 Wires Optional) Wiring The Sub Base The ZSM can be wired to receive four (4) operating status signals from the UCM (HEAT, COOL, SYSTEM “ON”, SER- VICE). Four (4) wires from the UCM should be connected to the appropriate terminals (7, 8, 9 &. Installation Figure 3 Zone Sensor Connection Diagram. Programming And Operation Initial Power-Up To set the time, simply press the (“+”) or (“-“) side of the KEY marked TIME.
Press the positive (“+”) side to advance the time in one minute intervals. Press the negative (“-“) Before applying power to the unit, verify that all wiring is side to decrease the time in one minute intervals. Programming And Operation Option Menu Refer to the Option Menu Screen illustration and the ZSM options and option values table with a description of each option. Refer to this table while viewing or programming The Option Menu is used to set all programmable options the sensor. Programming And Operation Option Function Option Value Default Description Morning warm-up 0 = Disabled When enabled, Heat is turned on if the Zone 1 = Enabled temperature is 2 degrees below the heat set point temperature when the program switches from unoccupied to occupied. Programming And Operation Programming Menu 9.
Pressing the ERASE KEY will erase the Start Time and Desired set points. They can be left blank or re-en- tered using steps 5 through 8. Before entering the Programming Menu, select the MODE of operation using the MODE KEY. Programming And Operation. Programming And Operation Weekly Program Record Monday Start Time Heat Set Point Cool Set Point Occupied/Unoccupied Morn Unocc Unocc Unocc Nite Unocc Tuesday Start Time Heat Set Point Cool Set Point Occupied/Unoccupied Morn Unocc Unocc Unocc Nite Unocc Wednesday Start Time Heat Set Point Cool Set Point Occupied/Unoccupied. Programming And Operation Temporary Override Menu Press the FAN KEY to program the fan for ON or AUTO operation during the override period.
The Temporary Override Menu is used to change tempera- Press and hold the UP and DOWN arrows simulta- ture set points, Mode of Operation, and the Zone status neously for 2 seconds to toggle the zone status be- (OCCUPIED or UNOCCUPIED) for a designated length of. Programming And Operation. Programming And Operation.
Troubleshooting Zone Sensor Status Indicators Terminal # 10 – (SERVICE Icon) ON - Indicates by a continuously illuminated icon that the unit requires service. The Unit Control Processor (UCP) has the capability of FLASHING – Indicates that a Fan Failure has communicating four input signals (HEAT, COOL, ON, SER- occurred and service is required. Troubleshooting Problem Solution Check the 24 VAC power supply at terminals 11 and 14 at the Zone Sensor. Actex p 1 study manual 2016 edition. Display does not come on. Verify that the terminal block is properly positioned on its pins. Check for 22 to 42 VDC between terminals 11 and 12 at the Zone Sensor.
No communications to the UCP.
File Name: Size: 1837 KB Uploaded: - This page is frequently updated and contains information about the book, past and current users, and the software. This page also contains a link to all known errors in the book, the accompanying slides, and the software. Since the solutions manual is distributed electronically, all known errors are immediately fixed and no list of errors is maintained. Instructors are advised to visit this site periodically; they can also register at this site to be notified of important changes by email. (read: privacy policy). Archives of A scholarship is money given to pay or offset school bills and lower the number of student loans you need. The quantities can range from only a few dollars to an all hen type.
Trane Baysens119a User Manual
This latter one is often referred to as a full experience. The counseling workplaces of most high faculties will have a guide that lists the more average scholarships out there. Under are descriptions of a few of the most often used sources.
Trane Baysens119a Thermostat Manual![]() Trane Baysens008b Manual
Many organizations be glad about scholarships through the local school methods. This is a way for a company to inspire scholars to look at topics relevant to that organizations business. A few of these scholarships are free however others have a stipulation of working for that particular business upon a hit of entirety of experiences. This is a type of student mortgage, as you need to pay off it by working off the debt.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |